Home > Amplifiers
Choose a sub category:
Cadence Image Dynamics
JBL Kicker
Zapco
Sort By:
Page of 2
Zapco
Our Price: $99.95

Kicker's DXA250.2 2-channel amplifier will deliver 30 watts RMS each to a pair of speakers from a very compact chassis that'll fit into a lot of places in your vehicle. This amp delivers around three times the power of a basic factory system, so you'll add a lot of clarity and punch to your sound. You can also use the DXA125.2 in bridged, 1-channel mode to power a subwoofer with 125 watts RMS..

Zapco ST X Series Amplifier ST-2X

Supplies Limited

2 Channel Full range class A/B
Power @ 2Ω: 2x85watts, 1x170 watts
RMS Rated Power @ < 0.05%THD
Power @ 2Ω: 2 x 80 watts
Power @ 4Ω: 2 x 50 watts
Bridged @ 4Ω: 1 x 160 watts


-Class-A/B bridgeable 12V amplifier
-2 channel bridgeable 12V amplifier
-Stable into 4 ohms bridged or 2 ohms stereo load
-STHD + Noise <0.05%
-Singal to Noise Ration >85dB
-Channel Separation >60dB
-Frequency Response 15Hz to 30KHz +/- 1dB
-Input Sensitivity .25volts to 5volts
-RCA Signal input and output connectors
-4-way protection circuitry
-thermal / over current / speaker short / DC
-Tested voltage & THD: 14.4V & less than 0.04%
-Dimensions in Inches : 6.4(W) x 1.8(H) x 6.1(L)

Kicker's DXA250.2 2-channel amplifier will deliver 30 watts RMS each to a pair of speakers from a very compact chassis that'll fit into a lot of places in your vehicle. This amp delivers around three times the power of a basic factory system, so you'll add a lot of clarity and punch to your sound. You can also use the DXA125.2 in bridged, 1-channel mode to power a subwoofer with 125 watts RMS..

Kicker's DXA250.2 2-channel amplifier will deliver 30 watts RMS each to a pair of speakers from a very compact chassis that'll fit into a lot of places in your vehicle. This amp delivers around three times the power of a basic factory system, so you'll add a lot of clarity and punch to your sound. You can also use the DXA125.2 in bridged, 1-channel mode to power a subwoofer with 125 watts RMS..
Zapco ST X Series Amplifier ST-500XM

Supplies Limited

1 channel; Low range class D
Power @ 1Ω: 1 x 500 watts
RMS Rated Power @ < 0.2%THD
Power @ 1Ω: 1 x 500 watts
Power @ 2Ω: 1 x 250 watts
Power @ 4Ω: 1 x 150 watts


Class-D Compact 12V amplifier
-1 channel 12V amplifier
-Stable into 1 ohms or 2 ohms load
-STHD + Noise <0.2%
-Singal to Noise Ration >70dB
-Efficiency >85dB
-Frequency Response 10Hz to 200Hz +/- 1dB
-Input Sensitivity .25volts to 5volts
-RCA Signal input and output connectors
-4-way protection circuitry
-thermal / over current / speaker short / DC
-Tested voltage & THD: 14.4V & less than 0.04%
-Dimensions in Inches : 6.4(W) x 1.8(H) x 7(L)
Zapco ST X Series Amplifier ST-4X
Supplies Limited

4 Channel Full range class A/B
Power @ 2Ω:2x105watts, 2x210 watts
Stereo, 2 ohms: 4 x 80 Watts
Bridged, 4 ohms: 2 x 180 Watts
Max RMS at 2 ohms <.5% THD at 1KHz
(4x105 Watts / 2x210 Watts)


-Class-A/B bridgeable 12V amplifier
-4 channel bridgeable 12V amplifier
-Stable into 4 ohms bridged or 2 ohms stereo load
-STHD + Noise <0.05%
-Singal to Noise Ration >85dB
-Channel Separation >60dB
-Frequency Response 15Hz to 30KHz +/- 1dB
-Input Sensitivity .25volts to 5volts
-RCA Signal input and output connectors
-4-way protection circuitry
-thermal / over current / speaker short / DC
-Tested voltage & THD: 14.4V & less than 0.04%
-Dimensions in Inches : 6.4(W) x 1.8(H) x 11.1(L)
Kicker's DXA500.1 amplifier will produce great-sounding bass — the kind that grabs your attention and makes listening to music in your car more fun. And this reliable little Kicker puts out up to 500 watts RMS from a very compact chassis that'll fit into a lot of places in most vehicles.
Zapco ST X Series Amplifier ST-5X

Supplies Limited

5 Channel Full range class A/B
Power@2Ω:4x120watts+1x240 watts
RMS Rated Power @ < 0.05%THD
Power@2Ω:4x100watts+1x240 watts
Power@4Ω:4x60watts+1x240 watts
Bridged@4Ω:2x200watts+1x240 watts



-Class-A/B bridgeable 12V amplifier
-5 channel bridgeable 12V amplifier
-Stable into 4 ohms bridged or 2 ohms stereo load
-STHD + Noise <0.05%
-Singal to Noise Ration >85dB
-Channel Separation >60dB
-Frequency Response 15Hz to 30KHz +/- 1dB
-Input Sensitivity .25volts to 5volts
-RCA Signal input and output connectors
-4-way protection circuitry
-thermal / over current / speaker short / DC
-Tested voltage & THD: 14.4V & less than 0.04%
-Dimensions in Inches : 6.4(W) x 1.8(H) x 15.3(L)
Zapco STD Series Amplifier ST-2D

Supplies Limited

Stereo, 4 ohms: 2 x 100 Watts
Stereo, 2 ohms: 2 x 200 Watts
Bridged, 4 ohms: 1 x 400 Watts
T.H.D. + Noise: <0.05% @ 4 ohms S/N Ratio: 90dBs.

Specifications:

-Class-D bridgeable 12V amplifier
-2/1 channel bridgeable 12V amplifier
-Stable into 4 ohms bridged or 2 ohms stereo load
-PWM MOSFET power supply
-18dB octave crossover slope
-Variable FULL / LP / HP Electronic Crossover -Variable bass boost
-RCA Signal input and output connectors
-4-way protection circuitry
-thermal / over current / speaker short / DC
-Tested voltage & THD: 14.4V & less than 0.05%
-Dimensions in Inches : 6.7(W) x 2.2(H) x 6.5(L)


The ST-2D. This little powerhouse has 100w RMS /Ch @ 4 ohms and 200w RMS/Ch @ 2 ohms with 400w RMS at 4 ohms mono. All this with <0.05% THD, 90dB S/N, Electronic Crossover and a Variable Bass Boost.

Rated 600W by Image Dynamics Monoblock High Fidelity Q Series Car Amplifier

• RMS: 250W x 1 @ 4 ohms, 400W x 1 @ 2 ohms, 600W x 1 @ 1 ohm
• Total RMS Power: 1200W
• Wired Bass Remote Included
• Bass Boost: 0-12 dB
• Preamp RCA Outputs
• Dimensions: 17-3/4"L x 8-1/2"W x 2-1/4"H


Zapco STD Series Amplifier ST-500DM

Supplies Limited

1 Channel Low range class D
Power @ 1Ω: 1 x 500 watts
RMS Rated Power @ < 0.2%THD
Power @ 1Ω: 1 x 500 watts
Power @ 2Ω: 1 x 310 watts
Power @ 4Ω: 1 x 160 watts

-Class-D 12V amplifier
-Single channel 12V bass amplifier
-Stable from 4 ohms to 1 ohm load
-PWM MOSFET power supply
-18dB octave crossover slope
-80Hz sub crossover
-30Hz Sub sonic filter
-RCA Signal input and output connectors
-4-way protection circuitry
-thermal / over current / speaker short / DC
-Tested voltage & THD: 14.4V & less than 0.2%
-Dimensions in Inches : 6.7(W) x 2.2(H) x 7.5(L)
Kicker's DXA1000.1 amplifier will reliably produce great-sounding bass — the kind that grabs your attention and makes listening to music in your car more fun. The DXA1000.1 puts out up to 1,000 watts RMS from a very compact chassis that'll fit into most vehicles.

650W RMS 2-Channel High Fidelity Q Series Car Amplifier

• RMS: 175W x 2 @ 4 ohms, 325W x 2 @ 2 ohms
• 650W x 1 Channel @ 4 Ohms Bridged
• Variable Bass Boost
• Variable High and Low Pass Filters
• Optically Isolate MOSFET Power Supply
• 5 Way System Protection Circuitry
• Subsonic Filter


Zapco STD Series Amplifier ST-4D


Supplies Limited

4 Channel Full range class D
Power @ 2Ω: 4 x 160 watts
Power @ 4Ω: 2 x 320 watts
RMS Rated Power @ < 0.05%THD
Power @ 2Ω: 4 x 160watts
Power @ 4Ω: 4 x 100watts
Bridged @ 4Ω: 2 x 320watts


-Class-D bridgeable 12V amplifier
-4/2 channel bridgeable 12V amplifier
-Stable into 4 ohms bridged or 2 ohms stereo load
-PWM MOSFET power supply
-18dB octave crossover slope
-Variable FULL / LP / HP Electronic Crossover -Variable bass boost
-RCA Signal input and output connectors
-4-way protection circuitry
-thermal / over current / speaker short / DC
-Tested voltage & THD: 14.4V & less than 0.05%
-Dimensions in Inches : 6.7(W) x 2.2(H) x 7.87(L)

1200 RMS High Fidelity Q Series Monoblock Car Amplifier

• RMS: 400W x 1 @ 4 ohms, 800W x 1 @ 2 ohms, 1200W x 1 @ 1 ohm
• Total RMS Power: 1200W
• Wired Bass Remote Included
• Bass Boost: 0-12 dB
• Preamp RCA Outputs
• Dimensions: 20"L x 8-1/2"W x 2-1/4"H


Kicker's DXA1500.1 amplifier will reliably produce great-sounding bass — the kind that grabs your attention and makes listening to music in your car more fun. The DXA1000.1 puts out up to 1,000 watts RMS from a very compact chassis that'll fit into most vehicles.

apco Z Series Amplifier Z-1K Linkable Dual / Mono Amplifier 10% off sale


1 Channel Low range SQ class D
Power @ 1Ω: 1 x 1000 watts
RMS Rated Power @ < 0.05%THD
Power @ 1Ω: 1 x 1000 watts
Power @ 2Ω: 1 x 560 watts
Power @ 4Ω: 1 x 300 watts
2 amps bridged @ 2Ω : 1700 watts


-Digital class-D linkable mono block amplifier
-Daisy-chain pass-through RCA output
-Stable into 4 ohms bridged or 2 ohms stereo load
-Dual MOS-FET PWM power supplies
-Stable into 1 ohm / 2 ohm parallel speaker connection
-24 dB Variable low pass (LPF) crossover
-12 dB Variable bass boost equalization
-0 - 180 degree variable phase shift
-24 dB Variable subsonic filter
-Selectable master and slave operation for strapped amplifiers
-Line input and master output / slave input
-Heavy duty cooper layer double sided epoxy PCB
-4 Guage (AWG) battery input connectors (Z-1KD)
-0 Guage (AWG) battery input connectors (Z-2KD/3KD)
-100% QC testing and warm up
-Efficiency: 86% at 4 ohm, 100 Hz
-RCA Signal input and output connectors
-4-way protection circuitry
-thermal / over current / speaker short / DC
-Tested voltage & THD: 14.4V & less than 0.05% at rated power
-Operating voltage : DC10V~16V power input
-Damping factor: > 350
-Wired remote control (optional)
-Dimensions in Inches : 7.5(W) x 3(H) x 12.25(L)
Zapco Z Series Amplifier 150.2 Z-150.2


2 Channel H-E SQ Full range class A/B
Power @ 2Ω: 2 x 250 watts
Power @ 4Ω: 1 x 500 watts
RMS Rated Power @ < 0.05%THD
Power @ 2Ω: 2 x 250 watts
Power @ 4Ω: 2 x 150 watts
Bridged @ 4Ω: 1 x 500 watts

-Class-AB bridgeable 12V amplifier
-2/1 channel bridgeable 12V amplifier
-Stable into 4 ohms bridged or 2 ohms stereo load
-PWM MOSFET power supply
-18dB octave crossover slope
-Variable FULL / LP / HP Electronic Crossover
-0dB, 6dB, 12dB selectable bass boost
-RCA Signal input and output connectors
-4-way protection circuitry
-thermal / over current / speaker short / DC
-Tested voltage & THD: 14.4V & less than 0.05% at rated power
-Operating voltage : DC10V~15.5V power input
-Wired remote control (optional)
-Dimensions in Inches : 7.5(W) x 3(H) x 13.25(L)
Zapco STD Series Amplifier ST-5D

Supplies Limited


5 Channel Full range class D
Power@2Ω:4x100watts+4Ω:1x350watts
RMS Rated Power @ < 0.05%THD
Power @ 2Ω:4x100watts+1x350watts
Power @ 4Ω:4x75watts+1x350watts
Bridged@4Ω:2x200watts+1x350watts


-Class-D bridgeable 12V amplifier
-5/3 channel bridgeable 12V amplifier
-Stable into 4 ohms bridged or 2 ohms stereo load
-PWM MOSFET power supply
-18dB octave crossover slope
-Variable FULL / LP / HP Electronic Crossover -Variable bass boost
-RCA Signal input and output connectors
-4-way protection circuitry
-thermal / over current / speaker short / DC
-Tested voltage & THD: 14.4V & less than 0.05%
-Dimensions in Inches : 6.7(W) x 2.2(H) x 10.5(L)
Zapco Digital Reference Amplifier





Stereo, 4 ohms:

Stereo, 2 ohms:

Bridged, 4 ohms:

T.H.D. + Noise:

S/N Ratio:

Slew Rate:

Damping Factor:

Dimensions:


2 x 100 Watts

2 x 170 Watts

1 x 330 Watts

<0.025% @ 4 ohms

>96dB

>29V/uS

>200 @ 4 ohms

16.38"L x7.12"W x 2.35"H

2-Channel Amp with On-Board Digital Processing



2-Channel Amp with On-Board Digital Processing

-SymbiLink Balanced Inputs

-On-Board, Full Function DSP

-Intelligent Rail Voltage Control

-Plays from ½ ohm to 4 ohm Stereo Loads

-USB Input for PC Control

-Optional DRC-SL In-Dash Remote Control

-Optional Digital Programming Network

-Ducted Flow Cooling

-Heavy-Duty, High-Current, Insulated Terminal Blocks

-Space Saving Flush Wiring Connections

-Heavy-Duty Mini ANL Fuse
-Bridgeable
-Three-Channel Capable

-Gate Drive Boost Circuit

-High-Current Bipolar Outputs

-Optically Isolated MOSFET Power Supply

-Three year warranty (If Authorized Dealer Installed)

-Quality ZAPCO construction

** Designed and Engineered in the USA **



This year ZAPCO introduces the DCS series of Reference amplifiers. This series shares the same platform as the analog Reference amps and the same power mix. This means lots of power and clean sound in both lines. The differences between the amps lie primarily in two areas. First, as the initials imply, the new series is digitally controlled. We know Zapco's not the first to do digital control�just the first to do it right. Each ZAPCO DCS amp features a USB input. This allows a PC to be hooked directly to the amp to set all functions. All functions can be set as stereo pairs or as individual channels. These DSP functions include:

1 - Output and input Gain

2 - Input mode: Rt, Lft, or Sum Mono

3 - Crossover mode: High Pass, Low pass, Band Pass

4 - Crossover Slope from 6 - 24dB

5 - Q-Bass Equalization

6 - Network Node Position

7 - Time Delay by both time and distance

8 - 10 bands of Parametric Equalization per Channel

Also available, is a half DIN controller to allow the settings to be made from the drivers seat without a computer. Also on each amp is a pair of RG connectors and a dip switch to "Address" the amp and "daisy chain" multiple amps. Once the amps are addressed you can use a single controller to operate up to 16 or more amplifiers. This allows you to set all functions of all amps in a system right from the driver's seat so you know how each adjustment affects the sound as you make it. Second, The DCS amps all feature our exclusive VRM circuitry which constantly compares the voltage rails to the output impedance. If the circuitry senses lower impedances it automatically adjusts the rail voltage to keep the amp in its power range between 4 ohms and 2 ohms. If the load remains below 2 ohms an LED will notify you to drop into the lower range where the amp will operate down to 1 ohm. Unlike other systems that simply turn down the gain, the VRM actually controls the operating voltage so the amp spends more time working at maximum efficiency.

Zapco Reference Amplifier


Mono, 4 ohms:

Mono, 2 ohms:

T.H.D. + Noise:

S/N Ratio:

Slew Rate:

Damping Factor:

Dimensions:


1 x 350 Watts

1 x 500 Watts

<0.04% @ 4 ohms

>80dB

>25V/uS

>250 @ 4 ohms

14.01"L x7.12"W x 2.35"H



Single-Channel Amp

-SymbiLink Balanced Inputs

-On-Board, Full Function DSP

-Intelligent Rail Voltage Control

-Plays from ½ ohm to 4 ohm Stereo Loads

-USB Input for PC Control

-Optional DRC-SL In-Dash Remote Control

-Optional Digital Programming Network

-Ducted Flow Cooling

-ZAPCO EHVC Output Circuitry

-Heavy-Duty, High-Current, Insulated Terminal Blocks

-Space Saving Flush Wiring Connections

-Heavy-Duty Mini ANL Fuse

-Gate Drive Boost Circuit

-High-Current Bipolar Outputs

-Optically Isolated MOSFET Power Supply

-Three year warranty (If Authorized Dealer Installed)

-Quality ZAPCO construction

** Designed and Engineered in the USA **
Zapco Reference Amplifier


Stereo, 4 ohms:

Stereo, 2 ohms:

Bridged, 4 ohms:

T.H.D. + Noise:

S/N Ratio:

Slew Rate:

Damping Factor:

Dimensions:


4 x 50 Watts

4 x 90 Watts

2 x 180 Watts

<0.046% @ 4 ohms

>95dB

>23V/uS

>160 @ 4 ohms

19.4"L x7.12"W x 2.35"H


4-Channel Amp
-SymbiLink Balanced Inputs

-On-Board, Full Function DSP

-Intelligent Rail Voltage Control

-Plays from ½ ohm to 4 ohm Stereo Loads

-USB Input for PC Control

-Optional DRC-SL In-Dash Remote Control

-Optional Digital Programming Network

-Ducted Flow Cooling

-Heavy-Duty, High-Current, Insulated Terminal Blocks

-Space Saving Flush Wiring Connections

-Heavy-Duty Mini ANL Fuse
-Bridgeable
-Three-Channel Capable

-Gate Drive Boost Circuit

-High-Current Bipolar Outputs

-Optically Isolated MOSFET Power Supply

-Three year warranty (If Authorized Dealer Installed)

-Quality ZAPCO construction

** Designed and Engineered in the USA **
Zapco Z Series Amplifier 150.4 Z-150.4

4 Channel H-E SQ Full range class A/B
Power @ 2Ω: 4 x 250 watts
Power @ 4Ω: 2 x 500 watts
RMS Rated Power @ < 0.05%THD
Power @ 2Ω: 4 x 250 watts
Power @ 4Ω: 4 x 150 watts
Bridged @ 4Ω: 2 x 500 watts


-Class-AB bridgeable 12V amplifier
-4/3/2 channel bridgeable 12V amplifier
-Stable into 4 ohms bridged or 2 ohms stereo load
-PWM MOSFET power supply
-Variable input sensitivity
-18dB octave crossover slope
-Variable FULL / LP / HP Electronic Crossover
-Variable bass boost
-RCA Signal input and output connectors
-4-way protection circuitry
-thermal / over current / speaker short / DC
-Tested voltage & THD: 14.4V & less than 0.05% at rated power
-Operating voltage : DC10V~15.5V power input
-Wired remote control (optional)
-Dimensions in Inches : 7.5(W) x 3(H) x 18.75(L)
Zapco Digital Reference Amplifier DC750.2
reference digital amplifier


Stereo, 4 ohms:

Stereo, 2 ohms:

Bridged, 4 ohms:

T.H.D. + Noise:

S/N Ratio:

Slew Rate:

Damping Factor:

Dimensions:


2 x 175 Watts

2 x 360 Watts

1 x 780 Watts

<0.04% @ 4 ohms

>90dB

>40V/uS

>1000 @ 4 ohms

24.4"L x7.12"W x 2.35"H





2-Channel Amp with On-Board Digital Processing

-SymbiLink Balanced Inputs

-On-Board, Full Function DSP

-Intelligent Rail Voltage Control

-Plays from ½ ohm to 4 ohm Stereo Loads

-USB Input for PC Control

-Optional DRC-SL In-Dash Remote Control

-Optional Digital Programming Network

-Ducted Flow Cooling

-Heavy-Duty, High-Current, Insulated Terminal Blocks

-Space Saving Flush Wiring Connections

-Heavy-Duty Mini ANL Fuse
-Bridgeable
-Three-Channel Capable

-Gate Drive Boost Circuit

-High-Current Bipolar Outputs

-Optically Isolated MOSFET Power Supply

-Three year warranty (If Authorized Dealer Installed)

-Quality ZAPCO construction

** Designed and Engineered in the USA **



This year ZAPCO introduces the DCS series of Reference amplifiers. This series shares the same platform as the analog Reference amps and the same power mix. This means lots of power and clean sound in both lines. The differences between the amps lie primarily in two areas. First, as the initials imply, the new series is digitally controlled. We know Zapco's not the first to do digital control�just the first to do it right. Each ZAPCO DCS amp features a USB input. This allows a PC to be hooked directly to the amp to set all functions. All functions can be set as stereo pairs or as individual channels. These DSP functions include:

1 - Output and input Gain

2 - Input mode: Rt, Lft, or Sum Mono

3 - Crossover mode: High Pass, Low pass, Band Pass

4 - Crossover Slope from 6 - 24dB

5 - Q-Bass Equalization

6 - Network Node Position

7 - Time Delay by both time and distance

8 - 10 bands of Parametric Equalization per Channel

Also available, is a half DIN controller to allow the settings to be made from the drivers seat without a computer. Also on each amp is a pair of RG connectors and a dip switch to "Address" the amp and "daisy chain" multiple amps. Once the amps are addressed you can use a single controller to operate up to 16 or more amplifiers. This allows you to set all functions of all amps in a system right from the driver's seat so you know how each adjustment affects the sound as you make it. Second, The DCS amps all feature our exclusive VRM circuitry which constantly compares the voltage rails to the output impedance. If the circuitry senses lower impedances it automatically adjusts the rail voltage to keep the amp in its power range between 4 ohms and 2 ohms. If the load remains below 2 ohms an LED will notify you to drop into the lower range where the amp will operate down to 1 ohm. Unlike other systems that simply turn down the gain, the VRM actually controls the operating voltage so the amp spends more time working at maximum efficiency.
Zapco Z Series Amplifier Z-2K Linkable Dual / Mono Amplifier

1 Channel Low range SQ class D
Power @ 1Ω: 2000 watts
RMS Rated Power @ < 0.05%THD
Power @ 1Ω: 1 x 2000 watts
Power @ 2Ω: 1 x 1100 watts
Power @ 4Ω: 1 x 570 watts
2 amps bridged @ 2Ω: 3400 watts



-Digital class-D linkable mono block amplifier
-Daisy-chain pass-through RCA output
-Stable into 4 ohms bridged or 2 ohms stereo load
-Dual MOS-FET PWM power supplies
-Stable into 1 ohm / 2 ohm parallel speaker connection
-24 dB Variable low pass (LPF) crossover
-12 dB Variable bass boost equalization
-0 - 180 degree variable phase shift
-24 dB Variable subsonic filter
-Selectable master and slave operation for strapped amplifiers
-Line input and master output / slave input
-Heavy duty cooper layer double sided epoxy PCB
-4 Guage (AWG) battery input connectors (Z-1KD)
-0 Guage (AWG) battery input connectors (Z-2KD/3KD)
-100% QC testing and warm up
-Efficiency: 86% at 4 ohm, 100 Hz
-RCA Signal input and output connectors
-4-way protection circuitry
-thermal / over current / speaker short / DC
-Tested voltage & THD: 14.4V & less than 0.05% at rated power
-Operating voltage : DC10V~16V power input
-Damping factor: > 350
-Wired remote control (optional)
-Dimensions in Inches : 7.5(W) x 3(H) x 19(L)
Zapco Digital Reference Amplifier DC1100.1 1000.1
reference digital amplifier


Mono, 4 ohms:

Mono, 2 ohms:

T.H.D. + Noise:

S/N Ratio:

Slew Rate:

Damping Factor:

Dimensions:


1 x 820 Watts

1 x 1100 Watts

<0.03% @ 4 ohms

>90dB

>40V/uS

>700 @ 4 ohms

24.4"L x7.12"W x 2.35"H




Single-Channel Amp with On-Board Digital Processing

-SymbiLink Balanced Inputs

-On-Board, Full Function DSP

-Intelligent Rail Voltage Control

-Plays from ½ ohm to 4 ohm Stereo Loads

-USB Input for PC Control

-Optional DRC-SL In-Dash Remote Control

-Optional Digital Programming Network

-Ducted Flow Cooling

-ZAPCO EHVC Output Circuitry

-Heavy-Duty, High-Current, Insulated Terminal Blocks

-Space Saving Flush Wiring Connections

-Heavy-Duty Mini ANL Fuse

-Gate Drive Boost Circuit

-High-Current Bipolar Outputs

-Optically Isolated MOSFET Power Supply

-Three year warranty (If Authorized Dealer Installed)

-Quality ZAPCO construction

** Designed and Engineered in the USA **



This year ZAPCO introduces the DCS series of Reference amplifiers. This series shares the same platform as the analog Reference amps and the same power mix. This means lots of power and clean sound in both lines. The differences between the amps lie primarily in two areas. First, as the initials imply, the new series is digitally controlled. We know Zapco's not the first to do digital control�just the first to do it right. Each ZAPCO DCS amp features a USB input. This allows a PC to be hooked directly to the amp to set all functions. All functions can be set as stereo pairs or as individual channels. These DSP functions include:

1 - Output and input Gain

2 - Input mode: Rt, Lft, or Sum Mono

3 - Crossover mode: High Pass, Low pass, Band Pass

4 - Crossover Slope from 6 - 24dB

5 - Q-Bass Equalization

6 - Network Node Position

7 - Time Delay by both time and distance

8 - 10 bands of Parametric Equalization per Channel

Also available, is a half DIN controller to allow the settings to be made from the drivers seat without a computer. Also on each amp is a pair of RG connectors and a dip switch to "Address" the amp and "daisy chain" multiple amps. Once the amps are addressed you can use a single controller to operate up to 16 or more amplifiers. This allows you to set all functions of all amps in a system right from the driver's seat so you know how each adjustment affects the sound as you make it. Second, The DCS amps all feature our exclusive VRM circuitry which constantly compares the voltage rails to the output impedance. If the circuitry senses lower impedances it automatically adjusts the rail voltage to keep the amp in its power range between 4 ohms and 2 ohms. If the load remains below 2 ohms an LED will notify you to drop into the lower range where the amp will operate down to 1 ohm. Unlike other systems that simply turn down the gain, the VRM actually controls the operating voltage so the amp spends more time working at maximum efficiency.

Zapco Z Series Amplifier 150.6 Z-150.6

6 Channel H-E SQ Full range class A/B
Power @ 2Ω: 6 x 230 watts
Power @ 4Ω: 3 x 450 watts
RMS Rated Power @ < 0.05%THD
Power @ 2Ω: 6 x 230 watts
Power @ 4Ω: 6 x 150 watts
Bridged @ 4Ω: 3 x 450 watts!



Class-AB bridgeable car amplifier
-7/6/5/3 channel bridgeable car amplifier
-Stable into 4 ohms bridged or 2 ohms stereo load
-PWM MOSFET power supply
-Input sensitivity (gain) control variable
-18dB octave crossover slope
-Variable Full/LP/HP selectable crossover
-(CH1/2/3/4)
-Variable Full/LPF Selectable crossover (CH5/6)
-Variable bass boost (CH5/6)
-Variable subsonic (CH5/6)
-RCA signal input connectors
-4-way protection circuitry
-(thermal / over current / speaker short / DC )
-Tested voltage & THD: 14.4V & less than 0.05% THD at rated power
-Operating voltage : DC10V~15.5V power input
-Wired remote control (optional)
-Dimensions in Inches : 7.48(W) x 2.36(H) x 22.44(L))
Zapco Digital Reference Amplifier DC1000.4 1000.4
reference digital amplifier


Stereo, 4 ohms:

Stereo, 2 ohms:

Bridged, 4 ohms:

T.H.D. + Noise:

S/N Ratio:

Slew Rate:

Damping Factor:

Dimensions:


4 x 150 Watts

4 x 250 Watts

2 x 500 Watts

<0.04% @ 4 ohms

>90dB

>36V/uS

>300 @ 4 ohms

24.4"L x7.12"W x 2.35"H



4-Channel Amp with On-Board Digital Processing

-SymbiLink Balanced Inputs

-On-Board, Full Function DSP

-Intelligent Rail Voltage Control

-Plays from ½ ohm to 4 ohm Stereo Loads

-USB Input for PC Control

-Optional DRC-SL In-Dash Remote Control

-Optional Digital Programming Network

-Ducted Flow Cooling

-ZAPCO EHVC Output Circuitry

-Heavy-Duty, High-Current, Insulated Terminal Blocks

-Space Saving Flush Wiring Connections

-Heavy-Duty Mini ANL Fuse
-Bridgeable
-Three-Channel Capable

-Gate Drive Boost Circuit

-High-Current Bipolar Outputs

-Optically Isolated MOSFET Power Supply

-Three year warranty (If Authorized Dealer Installed)

-Quality ZAPCO construction

** Designed and Engineered in the USA **



This year ZAPCO introduces the DCS series of Reference amplifiers. This series shares the same platform as the analog Reference amps and the same power mix. This means lots of power and clean sound in both lines. The differences between the amps lie primarily in two areas. First, as the initials imply, the new series is digitally controlled. We know Zapco's not the first to do digital control�just the first to do it right. Each ZAPCO DCS amp features a USB input. This allows a PC to be hooked directly to the amp to set all functions. All functions can be set as stereo pairs or as individual channels. These DSP functions include:

1 - Output and input Gain

2 - Input mode: Rt, Lft, or Sum Mono

3 - Crossover mode: High Pass, Low pass, Band Pass

4 - Crossover Slope from 6 - 24dB

5 - Q-Bass Equalization

6 - Network Node Position

7 - Time Delay by both time and distance

8 - 10 bands of Parametric Equalization per Channel

Also available, is a half DIN controller to allow the settings to be made from the drivers seat without a computer. Also on each amp is a pair of RG connectors and a dip switch to "Address" the amp and "daisy chain" multiple amps. Once the amps are addressed you can use a single controller to operate up to 16 or more amplifiers. This allows you to set all functions of all amps in a system right from the driver's seat so you know how each adjustment affects the sound as you make it. Second, The DCS amps all feature our exclusive VRM circuitry which constantly compares the voltage rails to the output impedance. If the circuitry senses lower impedances it automatically adjusts the rail voltage to keep the amp in its power range between 4 ohms and 2 ohms. If the load remains below 2 ohms an LED will notify you to drop into the lower range where the amp will operate down to 1 ohm. Unlike other systems that simply turn down the gain, the VRM actually controls the operating voltage so the amp spends more time working at maximum efficiency.
Zapco Z Series Amplifier Z-3K Linkable Dual / Mono Amplifier

1 Channel Low range SQ class D
Power @ 1Ω: 3000 watts
RMS Rated Power @ < 0.05%THD
Power @ 1Ω: 1 x 3000 watts
Power @ 2Ω: 1 x 1800 watts
Power @ 4Ω: 1 x 900 watts
2 amps bridged @ 2Ω: 5700 watts



-Digital class-D linkable mono block amplifier
-Daisy-chain pass-through RCA output
-Stable into 4 ohms bridged or 2 ohms stereo load
-Dual MOS-FET PWM power supplies
-Stable into 1 ohm / 2 ohm parallel speaker connection
-24 dB Variable low pass (LPF) crossover
-12 dB Variable bass boost equalization
-0 - 180 degree variable phase shift
-24 dB Variable subsonic filter
-Selectable master and slave operation for strapped amplifiers
-Line input and master output / slave input
-Heavy duty cooper layer double sided epoxy PCB
-4 Guage (AWG) battery input connectors (Z-1KD)
-0 Guage (AWG) battery input connectors (Z-2KD/3KD)
-100% QC testing and warm up
-Efficiency: 86% at 4 ohm, 100 Hz
-RCA Signal input and output connectors
-4-way protection circuitry
-thermal / over current / speaker short / DC
-Tested voltage & THD: 14.4V & less than 0.05% at rated power
-Operating voltage : DC10V~16V power input
-Damping factor: > 350
-Wired remote control (optional)
-Dimensions in Inches : 7.5(W) x 3(H) x 25.75(L)
Zapco Reference Amplifier


Stereo, 4 ohms:

Stereo, 2 ohms:

Bridged, 4 ohms:

Bridged, 2 ohms:

T.H.D. + Noise:

S/N Ratio:

Slew Rate:

Damping Factor:

Dimensions:


CH 1 - 4 / CH 5 - 6

4 x 50 Watts / 2 x 100 Watts

4 x 90 Watts / 2 x 180 Watts

2 x 180 Watts / 1 x 360 Watts

1 x 500 Watts

<0.05% @ 4 ohms

>95dB

>40V/uS

>160 @ 4 ohms

24.4"L x 7.12"W x 2.35"H



6-Channel Amp
-SymbiLink Balanced Inputs

-On-Board, Full Function DSP

-Intelligent Rail Voltage Control

-Plays from ½ ohm to 4 ohm Stereo Loads

-Ducted Flow Cooling

-Heavy-Duty, High-Current, Insulated Terminal Blocks

-Space Saving Flush Wiring Connections

-Heavy-Duty Mini ANL Fuse
-Bridgeable
-Three-Channel Capable

-Gate Drive Boost Circuit

-High-Current Bipolar Outputs

-Optically Isolated MOSFET Power Supply

-Three year warranty (If Authorized Dealer Installed)

-Quality ZAPCO construction

** Designed and Engineered in the USA **